Seed-hawk TOOLBAR 2015 Manuel d'utilisateur Page 34
- Page / 66
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SEED HAWK
®
2015 TOOLBAR OPERATOR’S MANUAL
1000
50
250
2000
100
275
3000
150
bar
4000
psi
200
1000
50
250
2000
100
275
3000
150
bar
4000
psi
200
324534
29
NOTE: When using a Seed
Hawk toolbar only, shank
pressure will be read on a
3000 psi gauge mounted
directly on the block.
4.6.1 Opener Shank Operation
Standard Toolbars
1. Ensure that there is power going to the Seed Hawk switch control box, and
that the ball valves on the back of opener hydraulic manifold are open.
2. Engage the tractor hydraulics lever that the RED band hose (opener circuit)
is connected to.
4. Moving in a forward direction, turn
on the PWM DOWN PRESSURE
switch, then turn on the SHANK/
LIQUID PUMP switch on. This will
engage the opener shanks.
Full Tractor Pressure
Inlet Pressure
Shank Pressure
Transducer
3. Lock the tractor hydraulics lever
that the GREEN banded hoses (wing
circuit) are connected to. The full
tractor pressure is shown on the top
right (4000 psi gauge) of the hydraulic
manifold block.
Refer to Section 4.4 pertaining to the control system being used.
5. Turing the min-max DOWN PRESSURE dial allows the user to increase or
decrease the desired packing pressure to achieve proper packing and penetra-
tion forces to seed.
When the proper amount of packing pressure is applied to the shank, the chain
that connects the seed and fertilizer knives will be pulled taught. Once the chain
is tight, take note of the packing pressure gauge reading. In optimal conditions,
an additional 200 psi of packing pressure is recommended. In wet conditions re-
duce the pressure accordingly to avoid over-compaction of soil, especially with
canola and other small seeds. Maximum Packing Pressure is 1500 psi.
6. Turn off the SHANK/LIQUID PUMP switch to disengage the opener
shanks.
0
500
1000
1500
2000
2500
3000
0
20
40
60
80
100
120
140
160
180
bar
psi
1000
50
250
2000
100
275
3000
150
bar
4000
psi
200
1000
50
250
2000
100
275
3000
150
bar
4000
psi
200
324350
Full Tractor Pressure
Shank Pressure
Inlet Pressure
- TOOLBAR 1
- Table of Contents 2
- 5.0 SBR 3
- 6.0 MAINTENANCE 3
- 7.0 TROUBLESHOOTING 4
- 9.0 INDEX 4
- 1.0 Introduction 6
- 1.1 Description of Machine 7
- 1.3 Machine Serial Number 8
- 2.0 Safety 10
- 2.2 Operator Responsibility 11
- 2.3 General Safety Practices 12
- 2.4 Maintenance Safety 13
- 2.5 Hydraulic Safety 14
- 2.6 Transport Safety 14
- 2.8 Tire Safety 15
- 2.7 Storage Safety 15
- 2.9 Safety Signs 16
- 2.9.2 Applied Safety Signs 17
- 2.9.3 Safety Sign Information 18
- SEED HAWK 19
- 3.0 Specications 20
- 3.1.4 Tire Hub Torque 21
- 3.2 Tire Pressure 22
- 12” (305 mm) Row Spacing 23
- 15” (381 mm) Row Spacing 23
- 10” (254 mm) Row Spacing 23
- 3.6 Openers 25
- 3.6.2 Seed Depth 26
- 4.0 Operation 28
- 28
- 4.2 Tractor Hook up 29
- 4.3 Pre-Operation Checklist 30
- Overviews 31
- 4.4.2 SCT 32
- Viper Pro™ Switch Box 32
- 4.5 Winging Down Toolbars 33
- 4.6 Winging Up Toolbars 33
- 4.6.1 Opener Shank Operation 34
- Standard Toolbars 34
- 4.7.1 Field Travel Speed 37
- 4.7.3 Mud Scraper Adjustment 38
- 4.8 Supply & Drop Tubes 39
- 4.8.2 Knife Options 40
- 4.8.3 Twin Wing 41
- 4.10 Seed Hawk 43
- Packer Tire 43
- 4.10.2 Muddy Soil Conditions 44
- Ammonia 45
- Hitch Toolbar 48
- (Loup III & SCT 48
- 6.0 Maintenance 50
- 6.3.2 Wheel Hubs 51
- 6.3.3 Wing Hinge Points 52
- 10 hrs or daily; inate to 53
- Cannot Adjust Shank Pressure 54
- Wings do not rise 55
- Gates will not open/close 56
- Openers will not lift 56
- Meter roller wont turn 57
- No fan speed 57
- Meter gate alarms going off 57
- 7.3 Nodes on SCT 58
- Implements 58
- 7.3.1 Node Light Denitions 59
- 7.3.2 Node Diagram 59
- 8.0 Wiring Harness 60
- 9.0 Index 62
- 3 1 7 0 6 6 66
Produits connexes et manuels pour Matériel de jardinage Seed-hawk TOOLBAR 2015
Matériel de jardinage Seed-hawk LOUP III & VIPER PRO 2015 - Hydraulic Drive Ca Manuel d'utilisateur
(70 pages)
(70 pages)
Matériel de jardinage Seed-hawk LOUP III & VIPER PRO 2014 - Hydraulic Drive Ca Manuel d'utilisateur
(72 pages)
(72 pages)
Matériel de jardinage Seed-hawk LOUP III & VIPER PRO 2013 - Hydraulic Drive Ca Manuel d'utilisateur
(49 pages)
(49 pages)
Matériel de jardinage Seed-hawk Hydraulic Drive 2010 Calibration Guide Manuel d'utilisateur
(33 pages)
(33 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.941 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels